Batimix WP-500 Elastic

Holderchem

Styrene Acrylic Elastomeric Coating

Description

BATIMIX WP-500 Elastic paint is a premium quality Styrene Acrylic Coating specialty designed for exterior application. This coating provides a high quality, excellent waterproof, elastic and protective finish.

Main Purpose

BATIMIX WP-500 Elastic is mainly used for waterproofing of different kind of surfaces like walls, ceilings, wood, and concrete. Suitable for outdoor and can be used for indoor applications.

Features

•Applies easily, with no unpleasant odor •Exceptionally easy to apply •Superior spatter resistance for application by roller •Provides a protective coating with high resistance against abrasion •Offers exceptional sealing •Eggshell/Satin finish •Creates a highly elastic and water resistant film that protects surfaces from weathering and moisture intrusion •Provides a mildew resistant coating

Properties

  • Vehicle type: Acrylic Copolymer
  • Pigment type : Titanium dioxide
  • Solid content (by weight): 50% ± 2
  • Recommended film thickness: Wet: 150 µm - Dry: 50 µm
  • Drying time (at 20 °C): To touch :30-60 min - To re-coat:1-2 hours - To fully cure:7 days
  • Dries by: Evaporation, coalescence
  • Viscosity: 20,000 cP ± 2,500
  • Elongation at break : 250%
  • Specific gravity: 1.3 ± 0.1
  • pH : 9 ± 1
  • Surface temperature at application: : Min: 16 °C - Max:32 °C
  • Thin with : Clean water
  • VOC level : Low

Health and Safety

Painting with BATIMIX WP-500 Elastic should be done with adequate ventilation. Do not breathe spray mist or sanding dust. Avoid contact with eyes and prolonged or repeated contact with skin. Wear eye protection and gloves during application or sanding. Close container after each use. Wash thoroughly after handling.

First Aid: In case of eye contact, flush with water for 15 minutes; for skin, wash with soap and water. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.

For additional safety directions, kindly refer to the corresponding Material Safety Data Sheet.

Direction of use

Mixing of paint: Stir thoroughly before and during use. Apply one or two coats, if needed.

Thinning: If necessary, to obtain desired application properties, you may add limited amounts of clean water to BATIMIX WP-500 Elastic. Stir thoroughly to mix the added water with the paint.

Surface preparation: Surfaces to be painted must be clean and free from dirt, dust, wax, soap, oil, grease, and water soluble materials. Water dispersed detergents (such as trisodium phosphate) and abrasive cleaners are more suitable than solvent-based solutions for surface cleaning. Rinse well to remove residues. Remove any peeling or scaling paint. Apply primer before and after filling nail holes, cracks, and other surface imperfections.

Unpainted surfaces: As mentioned above, the surface must be clean and thoroughly brushed with stiff fiber bristles to remove loose particles.

Repainted surfaces: Remove any peeling or scaling paint, and sand these areas to feather edges smooth with adjacent surfaces.

Primer: BATIMIX WP-500 Elastic is self priming coating, dilute with 50 % water to obtain a priming coat.

Application: BATIMIX WP-500 Elastic can be applied by brush, roller or airless spray. When using an airless spray, thinning may be required depending on the equipment used and the application conditions. Do not apply when air and/or surface temperature are below 16 °C. The average coverage rates are around 7.5 to 9 m2/liter, depending on the method of application, degree of substrate porosity and absorption level, etc.

Precautions: Wash with care to avoid scuffing and burnishing. Refrain from washing walls before paint is fully cured.

Warning: If you scrape sand or remove old paint, you may release lead dust which is known by its high toxicity. Exposure to lead can cause serious illness such as brain damage especially to children and pregnant women.

Storage

BATIMIX WP-500 has a minimum shelf life of 12 months if kept unopened. It must be stored in temperatures varying between 5 and 35 °C. It should not be subjected to direct sunlight.

Packages

  • 20 kg plastic pail
TS 2216Issue Date: 11-06-2026

The information and advice provided are based on current knowledge, Holderchem makes no warranty as to completeness or accuracy. {company} does not guarantee the merchantability or fitness of its products for particular purposes, and is not liable for any consequential or incidental damage or loss arising from the use of its products. HC®, HOLDERCHEM® and BATIMIX® are trademarks of {companyLegal}. Buyers should refer to recent product datasheets, trademark usage policies, and general conditions of sale on {website}. All rights reserved.