Batimix Tile Adhesive NS-400 White

Description

BATIMIX Tile Adhesive NS-400 White is a pre-packaged normal strength adhesive designed from a blend of Type I Portland cement, fillers, fine-graded sand, and synthetic additives.

Main Purpose

BATIMIX Tile Adhesive NS-400 White is ideal for fixing a wide range of ceramic, mosaic, and porcelain tiles smaller in area than 600 cm². Tiling can be done in inside areas like bathrooms, kitchens, stairs, and regular rooms. Admissible substrates include concrete, cement-based plasters, screeds, hollow blocks, and gypsum boards.

Features

BATIMIX Tile Adhesive NS-400 White can be applied quickly as pre-mixed. Upon the addition of water, the product becomes easy for troweling. It is applied vertically without sagging. It hardens without noticeable shrinkage. It forms a good bonding layer between the substrate and tiles.

Properties

• Appearance : powder
• Bulk density : around 1.51
• Mix ratio, for 100 g powder: 18 to 20 g of water
• Consistency of mix : viscous
• Pot life : around 1 hours
• pH: 12.6
• Application temperature : from +5 to +35 ºC
• Coverage: 2.5 to 6 kg / m²
• Open time (EN 1346) : around 20 minutes
• Adjustability time : around 30 minutes
• Slip resistance (EN 1308) : very good
• Wetting capability (EN 1347) : very good
• Wall grouting : after 6 hours
• Floor grouting: after 24 hours
• Set to light foot traffic : after 24 hours
• Ready for use : after 14 days
• Adhesion strength at 28 days (EN 1348) initial: 1.0 MPa
• Adhesion strength at 28 days (EN 1348) after heat ageing : 0.75 MPa
• Adhesion strength at 28 days (EN 1348) after water immersion : 0.9 MPa
• Adhesion strength at 28 days (EN 1348) after freeze/thaw cycles: 0.85 MPa
• Temperature after final cure: from -30 to +90 ºC
• Resistance to oils and alkalis: very good

Health and Safety

BATIMIX Tile Adhesive NS-400 White contains cement irritating to eyes and skin. In case of contact, with eyes, rinse immediately with plenty of water. Wear suitable gloves. For further information, kindly refer to the Material Safety Data Sheet.

Directions for Use

Substrate preparation: The surface of the substrate must be cured, mechanically strong, and thoroughly cleaned from all dust, loose particles, oil, wax, etc. BATIMIX Tile Adhesive NS-400 White works well on dry surfaces, but can also be applied on lightly dampened ones.

Mixing: One 20-kg bag of BATIMIX Tile Adhesive NS-400 White must be mixed with approximately 3.8 liters of clean water. Mixing should preferably be done with a slow-speed electric mixer for a minimum of 3 minutes to get a uniform lump free consistency. During hot weather, use cold water to increase the open time.

Application of the mix: Do not spread more than 1 m² of BATIMIX Tile Adhesive NS-400 White at a time. The mortar should be adjusted to the desired thickness using a notched trowel that will give coverage on the tiles back of at least 75% for all indoor walls and floors applications.

Installing the tiles: There is no need to dampen the tiles prior to installation. Apply a firm pressure to ensure good contact with the adhesive. The open time is around 20 minutes at 23 ºC. However, highly absorbent substrate or unfavorable weather conditions (high temperature, drying wind, or strong sun) may shorten this open time quite drastically to just a few minutes.

Constant checks should be conducted to determine if the adhesive is still fresh to the touch and capable of providing good adhesion to the tiles. In case a surface dried skin has formed on top of the adhesive, it is advisable to re-trowel the adhesive with a notched trowel which would help restoring the open time.

Grouting and protection: Wall joints between applied tiles can be grouted after 6 hours, and floor joints after 24 hours with any appropriate grout similar to BATIMIX Tile Grout series. All tiling made with BATIMIX Tile Adhesive NS-400 White must be protected from direct sun and washout for at least 5 to 7 days after application.

Specifications / Compliance with Standards

BATIMIX Tile Adhesive NS-400 White is manufactured to comply with EN 12004 for Tile Adhesives of Class C1: Normal Setting Cementitious Adhesive.

Mixing this product with BATIMIX Tile Adhesive L-430 instead of water improves the characteristics to meet the requirements of EN 12004 Class C2E, and those of EN 12002 Class S2 for deformable adhesives.

Storage

BATIMIX Tile Adhesive NS-400 White shelf life is six months from the production date if well stored in a closed dry place. Avoid freezing and excessive temperatures.

Packages

• 20 kg paper bag