Batimix Tile Adhesive F-452

Holderchem

Fast setting cementitious tile adhesive with reduced slip

Description

BATIMIX Tile Adhesive F-452 is a pre-packaged adhesive made from a blend of Portland cement type I, fillers, fine-graded sand, and synthetic additives incorporated to accelerate setting times and improve slippage resistance and bonding strength.

Main Purpose

BATIMIX Tile Adhesive F-452 is ideal for fixing a wide range of tiles such as ceramic, mosaic, porcelain, artificial, and natural stones on all types of floors, walls, and ceilings. It is used to tile inside and outside areas like bathrooms, kitchens, regular rooms, balconies, and terraces. Admissible substrates include concrete, cement-based plasters, screeds, polystyrene, hollow blocks, sound-deadening panels, and gypsum boards.

Features

BATIMIX Tile Adhesive F-452 has the following characteristics:

  • All tiling can be achieved in a clean and speedy manner
  • Mixed with water, this product becomes easy for troweling and ensures consistent fresh and hardened properties
  • Fast setting characteristics, suitable for areas that have to be ready for use in short periods of time
  • Enhanced resistance to vertical sagging and tile slippage
  • Limited shrinkage and strong layer bond between the substrate and tiles

Properties

  • Appearance : powder
  • Bulk density: around 1.5
  • Mix ratio, for 100 g powder: 18 to 20 g of water
  • Consistency of mix : viscous
  • Pot life : around 30 minutes
  • pH: 12.2
  • Application temperature : from +5 to +35 ºC
  • Coverage : 2.5 to 6 kg / m²
  • Open time (EN 1346) : around 10 minutes
  • Adjustability time : around 20 minutes
  • Slip resistance (EN 1308) : excellent
  • Wetting capability (EN 1347) : very good
  • Wall grouting : after 4 hours
  • Floor grouting : after 10 hours
  • Set to light foot traffic : after 10 hours
  • Ready for use : after 7 days
  • Adhesion strength at 28 days (EN 1348) initial : 1.0 MPa
  • Adhesion strength at 28 days (EN 1348) after heat ageing : 0.85 MPa
  • Adhesion strength at 28 days (EN 1348) after water immersion : 0.7 MPa
  • Adhesion strength at 28 days (EN 1348) after freeze/thaw cycles: 0.75 MPa
  • Temperature after final cure: from -20 to +80 ºC
  • Resistance to oils and alkalis: very good

Health and Safety

BATIMIX Tile Adhesive F-452 contains cement irritating to eyes and skin. In case of contact, rinse immediately with plenty of water. Wear suitable gloves. For further information, kindly refer to the Material Safety Data Sheet.

Directions for Use

Substrate preparation: The surface of the substrate must be cured, mechanically strong, and thoroughly cleaned from all dust, loose particles, oil, wax, etc. BATIMIX Tile Adhesive F-452 works well on dry surfaces, but can also be applied on lightly dampened ones.

Mixing: One 20-kg bag of BATIMIX Tile Adhesive F-452 must be mixed with approximately 3.8 liters of clean water. Mixing should preferably be done with a slow-speed electric mixer for a minimum of 3 minutes to get a uniform lump free consistency. During hot weather, use cold water to increase the open time.

Application of the mix: Do not spread more than 1 m² of BATIMIX Tile Adhesive F-452 at a time. The mortar should be adjusted to the desired thickness using a notched trowel that will give coverage on the tiles back of at least 75% for indoor walls and floors subjected to light foot traffic or 90% for heavy traffic floors and outdoor applications.

Installing the tiles: There is no need to dampen the tiles prior to installation. Apply a firm pressure to ensure good contact with the adhesive. The open time is around 10 minutes at 23 ºC. However, highly absorbent substrate or unfavorable weather conditions (high temperature, drying wind, or strong sun) may shorten this open time quite drastically to just a few minutes.

Constant checks should be conducted to determine if the adhesive is still fresh to the touch and capable of providing good adhesion to the tiles. In case a surface dried skin has formed on top of the adhesive, it is advisable to re-trowel the adhesive with a notched trowel which would help restoring the open time.

Grouting and protection: Wall joints between applied tiles can be grouted after 6 hours, and floor joints after 24 hours with any appropriate grout similar to BATIMIX Tile Grout series. All tiling made with BATIMIX Tile Adhesive F-452 must be protected from direct sun and washout for at least 5 to 7 days after application.

Specifications / Compliance with Standards

BATIMIX Tile Adhesive F-452 is manufactured to comply with EN 12004 for Tile Adhesives of Class C1FT: Fast Setting Cementitious Adhesive, Reduced Slip.

Mixing this product with BATIMIX Tile Adhesive L-430 instead of water improves the characteristics to meet the requirements of EN 12004 Class C2FT.

Storage

BATIMIX Tile Adhesive F-452 shelf life is six months from the production date if well stored in a closed dry place. Avoid freezing and excessive temperatures.

Packages

  • 20Kg Paper Bag
TS 5858Issue Date: 15-01-2021

The information and advice provided are based on current knowledge, Holderchem makes no warranty as to completeness or accuracy. {company} does not guarantee the merchantability or fitness of its products for particular purposes, and is not liable for any consequential or incidental damage or loss arising from the use of its products. HC®, HOLDERCHEM® and BATIMIX® are trademarks of {companyLegal}. Buyers should refer to recent product datasheets, trademark usage policies, and general conditions of sale on {website}. All rights reserved.