Batimix ES-700 Clear

Description

BATIMIX ES-700 Clear is an acrylic based sealer used for the preparation of substrates, prior to painting. This clear sealer yields a high quality surface that increases adhesion to subsequent application layers.

Main Purpose

BATIMIX ES-700 Clear is suitable for indoor and outdoor applications.

Features

• Applies easily, with no unpleasant odor
• Fast, simple clean up with soapy water
• Superior spatter resistance for roller application
• Brushes easily
• Offers exceptional hiding, sealing, and adhesion
• Provides a mildew resistant coating

Properties

• Vehicle type: Acrylic latex
• Pigment type : Titanium dioxide
• Solid content (by weight): 32% ± 2
• Recommended dry film thickness/coat : 60 µm
• Recommended dry film thickness : 17 µm
• Spreading rate (m²/L) : 17
• Spreading rate (m²/ 1 US Gallon): 63
• Spreading rate (m2/ 5US Gallon): 315
• Drying time at 20 °C (To touch) : 30 - 60 min
• Drying time at 20 °C (To re-coat) : 1-2 hours
• Drying time at 20 °C (To fully cure) : 7 days
• Dries by: Evaporation, coalescence
• Specific gravity : 1.04 ± 0.1
• pH : 9 ± 1
• Minimum surface temperature at application: 10°C
• Maximum surface temperature at application: 32°C
• Thin with: Clean water
• VOC level: Low
• PVC %: 0
• Volume Solid (VS) %: 28

Health and Safety

Sealing substrates with BATIMIX ES-700 Clear should be done with adequate ventilation. Do not breathe spray mist and sanding dust. Avoid contact with eyes and prolonged or repeated contact with skin. Wear eye protection and gloves during application or sanding. Close the container after each use and wash thoroughly after handling.

First Aid: In case of eye contact, flush with water for 15 minutes. For skin contact, wash with soap and water. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.

For additional safety directions, kindly refer to the corresponding Material Safety Data Sheet.

Directions for Use

Mixing of sealer: Stir thoroughly before and during use to obtain a homogenous and uniform solution.

Surface preparation: Surfaces to be painted must be clean and free from dirt, dust, wax, soap, oil, grease, and water-soluble materials. Water dispersed detergents (such as tri-sodium phosphate) and abrasive cleaners are more suitable than solvent-based solutions for surface cleaning. Rinse well to remove residues. Remove any peeling or scaling paint. Apply primer before and after filling nail holes, cracks, and other surface imperfections.

Unpainted surfaces: As mentioned above, the surface must be clean and thoroughly brushed with stiff fiber bristles to remove loose particles.

Repainted surfaces: Remove any peeling or scaling paint, and sand these areas to featheredges smooth with adjacent surfaces.

Application: BATIMIX ES-700 Clear is applied by brush, roller or airless spray. When using an airless spray, thinning may be required depending on the equipment used and the application conditions. Do not apply when air and/or surface temperatures are below 10 °C. Apply one or two coats, if needed. The average coverage rate is around 7.5 to 9 m²/liter, depending on the method of application, degree of substrate porosity and absorption level, etc.

Precautions: Wash with care to avoid scuffing and burnishing. Refrain from washing walls before paint is fully cured.

Warning: If you scrape sand or remove old paint, you may release lead dust, which is known for its high toxicity. Exposure to lead can cause serious illnesses and brain damage, especially to children and pregnant women.

Storage

BATIMIX ES-700 Clear has a minimum shelf life of 12 months if kept unopened. It must be stored at temperatures ranging from 5 to 40 °C. It should not be subjected to direct sunlight.

Packages

• 5 US gallon plastic pail
• 1 US gallon plastic pail