Batimix EMS-1450 Roll

Description

BATIMIX EMS-1450 Roll paint is a medium shade premium quality acrylic paint used for decorative and architectural purposes. This medium shade colored paint yields a high quality, waterproof, elastic and protective finish.

Main Purpose

BATIMIX EMS-1450 Roll paint is applied to different kinds of surfaces, like walls, ceilings, wood, and concrete. It is mostly suitable for indoor and outdoor uses.

Features

• Applies easily and has no unpleasant odor
• Superior spatter resistance for roller application
• Provides a protective coating with high resistance against abrasion
• Offers exceptional hiding and sealing
• Creates a highly elastic and water-resistant film that protects surfaces from weathering and moisture intrusion
• Provides a mildew-resistant coating

Properties

• Vehicle type: Styrene acrylic
• Pigment type: Titanium dioxide
• Solid content: 50% ± 2
• Recommended wet film thickness: 130 µm
• Recommended dry film thickness: 70 µm
• Drying time at 20°C (To touch): 30 - 60 min
• Drying time at 20°C (To re-coat): 1 - 2 hours
• Drying time at 20°C (To fully cure): 7 days
• Dries by: Evaporation, coalescence
• Viscosity: 40,000 cP ± 4,000
• Elongation at break: 150%
• Specific gravity: 1.3 ± 0.1
• pH: 9 ± 1
• Minimum surface temperature at application: 16°C
• Maximum surface temperature at application: 32°C
• Thin with: Clean water
• VOC level: low

Health and Safety

Painting with BATIMIX EMS-1450 Roll should be done with adequate ventilation. Do not breathe spray mist and sanding dust. Avoid contact with eyes and prolonged or repeated contact with skin. Wear eye protection and gloves during application or sanding. Close the container after each use and wash thoroughly after handling.

First Aid: In case of eye contact, flush with water for 15 minutes. For skin contact, wash with soap and water. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.

For additional safety directions, kindly refer to the corresponding Material Safety Data Sheet.

Direction for Uses

Mixing of paint: Stir thoroughly before and during use. Apply one or two coats, if needed.

Thinning: If necessary, to obtain desired application properties, you may add limited amounts of clean water to BATIMIX EMS-1450 Roll. Stir thoroughly to mix the added water with the paint.

Surface preparation: Surfaces to be painted must be clean and free from dirt, dust, wax, soap, oil, grease, and water-soluble materials. Water dispersed detergents (such as tri-sodium phosphate) and abrasive cleaners are more suitable than solvent-based solutions for surface cleaning. Rinse well to remove residues. Remove any peeling or scaling paint. Apply primer before and after filling nail holes, cracks, and other surface imperfections.

Unpainted surfaces: As mentioned above, the surface must be clean and thoroughly brushed with stiff fiber bristles to remove loose particles.

Repainted surfaces: Remove any peeling or scaling paint, and sand these areas to featheredges smooth with adjacent surfaces.

Primer: For maximum adhesion strength, you may use BATIMIX primers before applying the paint.

Application: BATIMIX EMS-1450 Roll can be applied by brush, roller or airless spray. When using an airless spray, thinning may be required depending on the equipment used and the application conditions. Do not apply when air and/or surface temperatures are below 16 °C. The average coverage rates are around 7.5 to 9 m2/liter, depending on the method of application, degree of substrate porosity and absorption level, etc.

Precautions: Wash with care to avoid scuffing and burnishing. Refrain from washing walls before paint is fully cured.

Warning: If you scrape sand or remove old paint, you may release lead dust, which is known for its high toxicity. Exposure to lead can cause serious illnesses and brain damage, especially to children and pregnant women.

Storage

BATIMIX EMS-1450 Roll has a minimum shelf life of 12 months if kept unopened. It must be stored at temperatures ranging from 5 to 40 °C. It should not be subjected to direct sunlight.

Packages

• 25 kg plastic pail
• 6 kg plastic pail