Batimix EHS-630 Satin

Description

BATIMIX EHS-630 Satin paint is a high-shade premium quality acrylic paint. This colored paint provides a high-quality finish that can be washed clean with soap and water and creates a decorative and protective satin surface that resists the adsorption of stains.

Main Purpose

BATIMIX EHS-630 Satin paint is mainly used for outdoor, on concrete, masonry, and previously painted surfaces. It can also be used for indoor application.

Features

• An attractive, washable satin finish
• Exceptionally easy to apply
• Fast, simple clean up with minimum wet rubbing
• Superior spatter resistance for application by roller
• Offers exceptional hiding and sealing
• Resistant to soaps, detergents, and household cleaners
• Provides a mildew-resistant coating
• Resists the changes in weather conditions

Properties

• Binder type: Acrylic latex
• Solid content (by weight): 39% ±2
• Recommended wet film thickness/coat: 100 µm
• Recommended dry film thickness/coat: 32 µm
• Drying time at 20°C(to touch): 30-60 min
• Drying time at 20°C(to re-coat): 1-2 hours
• Drying time at 20°C(to fully cure): 7 days
• Dries by: Evaporation, coalescence
• Viscosity (S4/10/25°C): 5,700 cP ±1,000
• PVC: 19% ±2
• Specific gravity: 1.1 ±0.05
• pH: 8.5 ±0.5
• 60° Gloss: 20-35
• Minimum surface temperature at application: 16 °C
• Maximum surface temperature at application: 32 °C
• Thin with: Clear water

Health and Safety

Painting with BATIMIX EHS-630 Satin should be done with adequate ventilation. Do not breathe spray mist and sanding dust. Avoid contact with eyes and prolonged or repeated contact with skin. Wear eye protection and gloves during application or sanding. Close the container after each use and wash thoroughly after handling.

First Aid: In case of eye contact, flush with water for 15 minutes. For skin contact, wash with soap and water. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.

For additional safety directions, kindly refer to the corresponding Material Safety Data Sheet.

Directions for Use

Mixing of paint: Stir thoroughly before and during use. Apply one or two coats, if needed.

Thinning: If necessary, to obtain desired application properties, you may add limited amounts of clean water to BATIMIX EHS-630 Satin. Stir thoroughly to mix the added water with the paint.

Surface preparation: Surfaces to be painted must be clean and free from dirt, dust, wax, soap, oil, grease, and water soluble materials. Water dispersed detergents (such as trisodium phosphate) and abrasive cleaners are more suitable than solvent-based solutions for surface cleaning. Rinse well to remove residues. Remove any peeling or scaling paint. Apply primer before and after filling nail holes, cracks, and other surface imperfections.

Unpainted surfaces: As mentioned above, the surface must be clean and thoroughly brushed with stiff fiber bristles to remove loose particles.

Repainted surfaces: Remove any peeling or scaling paint, and sand these areas to feather edges smooth with adjacent surfaces.

Primer: For maximum adhesion strength, you may use BATIMIX primers before applying the paint.

Application: BATIMIX EHS-630 Satin can be applied by brush, roller or airless spray. When using an airless spray, thinning may be required depending on the equipment used and the application conditions. Do not apply when air and/or surface temperature are below 16 °C. The average spreading rate per coat is around 10 m²/liter, depending on the method of application, degree of substrate porosity and absorption level, etc.

Precautions: Wash with care to avoid scuffing and burnishing. Refrain from washing walls before paint is fully cured.

Storage

BATIMIX EHS-630 Satin has a minimum shelf life of 12 months if kept unopened. It must be stored in temperatures varying between 5 and 40 °C. It should not be subjected to direct sunlight.

Packages

• 5 U.S. gallons
• 1 U.S. gallon